石家庄半电动堆垛车
石家庄半电动堆垛车
产品价格:¥1(人民币)
  • 规格:1
  • 发货地:石家庄
  • 品牌:
  • 最小起订量:11
  • 免费会员
    会员级别:试用会员
    认证类型:企业认证
    企业证件:通过认证

    商铺名称:河北骏豪机械设备有限责任公司

    联系人:张帅(先生)

    联系手机:

    固定电话:

    企业邮箱:2067778308@qq.com

    联系地址:河北省石家庄市长安区胜利北街219号花中锦五金机电市场274-275号

    邮编:50000

    联系我时,请说是在线缆网上看到的,谢谢!

    商品详情

      河北骏豪机械设备有限责任公司

      联系人:张经理13933000298

      堆高车起重无力或不能起重原因:齿轮泵与泵提磨损过度;换向阀内的溢流阀高压不当;油压管路漏油;液压油油温过度;门架滑架存在卡阻现象;油泵电机转速过低。解决方法:更换磨损或齿轮泵;重新调整;检查并修复;更换不合格的液压油并检查油温度升高的原因;检查并调整;检查电机并排除故障。
      Stacker crane lifting to reason: the gear pump and the pump provided excessive wear; high pressure solenoid valve relief valve in hydraulic pipeline improper; leakage; excessive oil temperature; the door frame carriage are blocked; the pump motor speed is too low. Solution: replace wear or gear pumps; readjust; check and repair; replace faulty hydraulic oil and check the cause of elevated oil temperature; check and adjust; check motor and troubleshoot.

      三月,醉一场青春的流年。我们珍惜三月,就像我们珍惜来之不易的幸福青春。三月的雨,三月的风,三月的春光,三月的花香,让我们沉醉不知归路,兴尽晚回舟。在这样一场盛大而清新的流年,我们懂得,青春是一种一去不复返的风景,应当好好保护;青春是一种美丽而活跃的热情,我们必须耐心保持;青春是一种来之不易的懂得,我们必须细心呵护。
       
      堆高车油泵压力不足或速度过慢原因:泵盖槽内密封圈损坏,内漏过多;齿轮磨损;油泵电机转速降低;管道中有异物堵塞。解决方法:更换;更换油泵;检查整流子,清除片间积炭,调整炭刷位置;检查清洗。
      Stack pump pressure or speed is too slow: the pump cover groove sealing ring damage, too much leakage; gear wear; oil pump motor speed down; pipe in the foreign body plug. Solution: replacement; replacement pump; check the commutator, clearance between coke, adjust the brush position check and clean.
      三月,醉一场青春的流年。风过无痕,花开向暖。无论是哪一年的三月,都是青春是里最美丽的花朵,都是青春里最难舍的风景,都是青春里最妩媚的清香。无论在哪一年的三月,无论我们有没有老去,心中的青春千万不能割舍,心中的青春永远跳动着快乐,心中的青春永远伴随我们一生一世。
       
      堆高车电器运作不不正常:原因:电器盒内微动开关损坏或位置调整不当;主电路保险丝或控制电器保险丝熔断;电池电压过低;接触器触点烧毛,或污物太多造成接触不良;触点不动作。解决方法:更换微动开关,重新调整位置;更换同型号保险丝;重新充电;修理触点,调整或更换接触器;检查接触器线圈有无断路或更换接触器。
      Electric stacker operation is not normal: Reason: electric box micro switch is damaged or improperly adjusted position; the main circuit control electric fuse or fuse; the battery voltage is too low; singeing contactor, or too much dirt caused by poor contact; contact action. Solution: replace the microswitch, readjust the position, replace the same type fuse, recharge the battery, repair the contact, adjust or change the contactor, check whether the contactor coil is broken or replace the contactor.




    在线询盘/留言
  • 0571-87774297